Electricity and Energy

Содержание

Слайд 2

QUESTION 1 A car headlamp is rated at 55W.The light produced

QUESTION 1

A car headlamp is rated at 55W.The light produced is

20% of the total energy transferred by the lamp.
Calculate the energy transferred by the lamp as light in 30s.
Слайд 3

QUESTION 2 A crate of mass 200kg is pushed 20m across

QUESTION 2

A crate of mass 200kg is pushed 20m across a

floor with a force of 150N.
Calculate the work done in pushing the crate along the floor if the force of friction acting on the crate is 50N.
Слайд 4

An engine applies a force of 2000N to move a lorry

An engine applies a force of 2000N to move a lorry

at a constant speed.
The lorry travels 100m in 16s.
Calculate the power developed by the engine.

QUESTION 3

Слайд 5

An arrow of mass 150g is fired from a bow as

An arrow of mass 150g is fired from a bow as

shown below. The archer pulls the string back a distance of 0.50m and exerts a force of 300N on the arrow as it is fired.
Calculate the maximum kinetic energy gained by the arrow.

QUESTION 4

Слайд 6

A power station has an efficiency of 40%. The input power

A power station has an efficiency of 40%.
The input power

to the station is 1600MW.
Calculate the useful power output.

QUESTION 5

Слайд 7

A person using the exercise bike below, pedals against 300N of

A person using the exercise bike below, pedals against 300N of

frictional forces applied to the wheel of circumference 1.5m by the brake.
How much work is done against friction with one turn of the wheel?
b) Calculate the average power produced if the wheel turns 500 times in 5 minutes.

QUESTION 6

Слайд 8

An electric motor raises a crate of mass 500kg through a

An electric motor raises a crate of mass 500kg through a

height of 12m in 8s.
Calculate or find:
a) Ep gained by the crate.
b) Minimum power rating of the electric motor.

QUESTION 7

Слайд 9

A ski lift with a gondola of mass 2000kg travels to

A ski lift with a gondola of mass 2000kg travels to

a height of 540m from the base station.
a) Calculate the gain in gravitational potential energy of the gondola.
b) Calculate the speed of the gondola if it has 36,000J of kinetic energy at one stage in the journey.

QUESTION 8

Слайд 10

The speed-time graph below shows the motion of a 700kg car.

The speed-time graph below shows the motion of a 700kg car.
a)

Calculate the kinetic energy at A.
b) State the work done in bringing the car to a halt between B and C.

QUESTION 9

Слайд 11

The graph below shows the speed-time graph of a 0.50kg object

The graph below shows the speed-time graph of a 0.50kg object

when it is involved in a collision.
Calculate the kinetic energy lost by the object when it is in a collision between S and T.

QUESTION 10

Слайд 12

A 0.02kg mass detaches from a thread before the vehicle is

A 0.02kg mass detaches from a thread before the vehicle is

released from rest and falls 0.80m to the floor.
Calculate or find:
a) Gravitational potential energy stored in the mass before it fell.
b) Speed of the mass before it hits the floor.

QUESTION 11

Слайд 13

A child of mass 50kg is playing on a water slide

A child of mass 50kg is playing on a water slide

as shown below.
Calculate or find:
a) Gravitational potential energy of the child at the top.
b) Length of the slide, if 20N of frictional force acts on the child producing 1400J of heat energy.

QUESTION 12

Слайд 14

The voltage of an electrical supply is a measure of the QUESTION 13

The voltage of an electrical supply is a measure of the

QUESTION

13
Слайд 15

Which of the following statements are true about electrical conductors QUESTION 14

Which of the following statements are true about electrical conductors

QUESTION 14

Слайд 16

A charge of 15C passes through a resistor in 12s. The

A charge of 15C passes through a resistor in 12s. The

potential difference across the resistor is 6V.
Calculate the power developed in the resistor.

QUESTION 15

Слайд 17

A rechargeable battery is labelled 2600mAh. Calculate the charge stored in the battery. QUESTION 16

A rechargeable battery is labelled 2600mAh.
Calculate the charge stored in the

battery.

QUESTION 16

Слайд 18

The current in an 8Ω resistor is 2A. Calculate the charge

The current in an 8Ω resistor is 2A.
Calculate the charge passing

through the resistor in 40s.

QUESTION 17

Слайд 19

Identify the circuit symbols X,Y and Z. QUESTION 18

Identify the circuit symbols X,Y and Z.

QUESTION 18

Слайд 20

The mains voltage in the UK is 230V ac. Which row

The mains voltage in the UK is 230V ac.
Which row in

the table below shows the peak voltage and the mains supply?

QUESTION 19

Слайд 21

A student has two electrical power supplies. One is an ac

A student has two electrical power supplies.
One is an ac

supply and the other is a dc supply.
Label which supply in the diagrams below are ac and dc and describe them both in terms of electron flow.

QUESTION 20

Слайд 22

A circuit is set up as shown below. Which switch or

A circuit is set up as shown below.
Which switch or switches

must be closed to light lamp L1 only?

QUESTION 21

Слайд 23

Which of the following statements that an LHS Physics student made are true? QUESTION 22

Which of the following statements that an LHS Physics student made

are true?

QUESTION 22

Слайд 24

QUESTION 23 A student is given a task of combining three

QUESTION 23

A student is given a task of combining three resistors

from a pack containing:
30Ω, 50 Ω, 80 Ω, 120 Ω and 270 Ω.
Show by calculation which three resistors(In series or parallel?) should be used to give
a) the largest combined resistance
b) the lowest combined resistance.
Слайд 25

Which circuit below is used to find the resistance of Resistor R2? QUESTION 24

Which circuit below is used to find the resistance of Resistor

R2?

QUESTION 24

Слайд 26

In the circuit below the resistance of the variable resistor is

In the circuit below the resistance of the variable resistor is

increased.
Which row in the table shows the effect on the ammeters and voltmeters?

QUESTION 25

Слайд 27

Calculate the potential difference across the 2Ω resistor in the circuit below. QUESTION 26

Calculate the potential difference across the 2Ω resistor in the circuit

below.

QUESTION 26

Слайд 28

Calculate the following from the circuit below: a) Current through the

Calculate the following from the circuit below:
a) Current through the resistor.
b)

Power supplied to the resistor.

QUESTION 27

Слайд 29

In the circuit below the current in the lamp is 1.5A

In the circuit below the current in the lamp is 1.5A

and the reading on the voltmeter is 6V.
Calculate the power in the lamp.

QUESTION 28

Слайд 30

Calculate the total resistance between X and Y in the network below. QUESTION 29

Calculate the total resistance between X and Y in the network

below.

QUESTION 29

Слайд 31

Calculate the following in the circuit below: a) Total resistance between

Calculate the following in the circuit below:
a) Total resistance between Y

and Z.
b) Total resistance between W and X.
c) Voltage across the 2Ω resistor when the current in the 4Ω resistor is 0.10A.

QUESTION 30

Слайд 32

QUESTION 31 Calculate the following from the circuit below: a) Total

QUESTION 31

Calculate the following from the circuit below:
a) Total resistance in

the circuit.
b) Reading on the ammeter
c) Reading on the voltmeter
d) Power developed in the 2Ω series resistor.
Слайд 33

Calculate or find the following from the rating plate of an

Calculate or find the following from the rating plate of an

electric food mixer.
a) Resistance of the food mixer
b) Current passing through the food mixer.
c)The fuse required for the food mixer plug.

QUESTION 32

Слайд 34

The graph below shows the temperature of a substance over a

The graph below shows the temperature of a substance over a

period of time.
Which row in the table shows the sections of the graph when the substance is changing state?

QUESTION 33

Слайд 35

The specific latent heat of fusion of a substance is the

The specific latent heat of fusion of a substance is the

heat energy required to

QUESTION 34

Слайд 36

100g of solid is heated by a 50W heater. Calculate the

100g of solid is heated by a 50W heater.
Calculate the specific

latent heat of fusion of the substance using the graph below.

QUESTION 35

Слайд 37

A block of ice of mass 1.5kg is placed in a

A block of ice of mass 1.5kg is placed in a

room at 20°C. If the block of ice is at 0°C, then calculate the minimum energy required to turn the ice at 0°C into water at 20°C.

QUESTION 36

Слайд 38

A sample of water at a temperature of 100°C absorbs 23,000J

A sample of water at a temperature of 100°C absorbs 23,000J

of heat energy.
Calculate the mass of water turned into steam at 100°C using the necessary information from the data book.

QUESTION 37

Слайд 39

A fridge/freezer has water and ice dispensers. 0.15kg of water flows

A fridge/freezer has water and ice dispensers.
0.15kg of water flows into

the freezer at 14°C and is cooled to 0°C.
a) Calculate the heat energy removed when the water cools.
b) Calculate how much heat energy is released when 0.15kg of water at 0°C changes to 0.15kg of ice at 0°C.

QUESTION 38

Слайд 40

QUESTION 39

QUESTION 39

Слайд 41

From the experiment and the data obtained above, calculate or find:

From the experiment and the data obtained above, calculate or find:
Specific

heat capacity of the water.
b) Power rating of the immersion heater.
c) How does the calculated reading in a) compare with the accepted value in the data book?
d) How could the experiment be improved to provide a specific heat capacity nearer the accepted value in the data book?

QUESTION 39 (Cont’d)

Слайд 42

On the planet Mercury the surface temperature at night is -173°C

On the planet Mercury the surface temperature at night is -173°C

and during the day it is 307°C.
A rock of mass 80kg lying on the surface of the planet absorbs 3.46 x 107J of heat energy during the day.
a) Calculate the specific heat capacity of the rock.
b) Calculate how long it would take to release
3.46 x 107J of heat energy during the night if it is released at 1500W.

QUESTION 40

Слайд 43

A rectangular block of wood of mass 2000g has dimensions of

A rectangular block of wood of mass 2000g has dimensions of

2m x 1m x 0.1m.
Calculate the greatest pressure that the block can exert when lying on a level surface.

QUESTION 41

Слайд 44

The air pressure inside a passenger cabin of an aircraft is

The air pressure inside a passenger cabin of an aircraft is

92,000Pa during a flight with the pressure outside being 42,000Pa.
Calculate the resultant force on the cabin door of area 3m2, caused by the difference in air pressure.

QUESTION 42

Слайд 45

Which of the following statements that an LHS Physics student wrote

Which of the following statements that an LHS Physics student wrote

in her notebook are true?

QUESTION 43

Слайд 46

A liquid is heated from 16°C to 40°C. What is the

A liquid is heated from 16°C to 40°C.
What is the temperature

rise in the Kelvin Scale?

QUESTION 44

Слайд 47

Which of the following graphs illustrates the correct relationship between the

Which of the following graphs illustrates the correct relationship between the

pressure P and the volume V of a fixed mass of gas at constant temperature?

QUESTION 45

Слайд 48

A student uses the apparatus shown below to investigate the relationship

A student uses the apparatus shown below to investigate the relationship

between the pressure and the volume of a fixed mass of gas at constant temperature.
a) Using all of the data, establish the relationship between the pressure and the volume of the gas.
b) Use the kinetic model to explain the change in pressure as the volume of the gas decreases.

QUESTION 46

Слайд 49

On a cold morning at 2°C the pressure of a car

On a cold morning at 2°C the pressure of a car

tyre was 3x105Pa.
After a motorway run the temperature of air in the tyre rose to 57°C, with the volume of the air in the tyre staying constant.
Calculate the pressure of the tyre when its temperature reached 57°C.

QUESTION 47

Слайд 50

A balloon with a volume of 6.0m3 contains a fixed mass

A balloon with a volume of 6.0m3 contains a fixed mass

of gas at a temperature of 300K and a pressure of 2.0kPa.
The gas is heated to 600K and the pressure drops to 1.0kPa.
Calculate the new volume of the balloon.

QUESTION 48

Слайд 51

Oxygen is held inside a cylinder at a pressure of 2.82x106Pa

Oxygen is held inside a cylinder at a pressure of 2.82x106Pa

and temperature of 19°C.
Calculate the pressure of the gas in the cylinder if it is moved to a storage room at 5°C.

QUESTION 49

Слайд 52

The apparatus below was used to investigate the relationship between the

The apparatus below was used to investigate the relationship between the

volume and temperature of a fixed mass of gas at constant pressure.
A table of results was then taken and recorded.

QUESTION 50

Слайд 53

A student investigates the relationship between the volume and the temperature

A student investigates the relationship between the volume and the temperature

of a fixed mass of gas at constant pressure.
Using all of the data, establish the relationship between the temperature and volume for the trapped air.
Calculate the volume of the trapped air when the temperature of the water is 65°C.
Use the Kinetic Model to explain the change in volume as the temperature increases in the experiment.

QUESTION 50 (Cont’d)

Слайд 54

Which row in the table shows the symbols for an LED

Which row in the table shows the symbols for an LED

and a NPN transistor.

QUESTION 51

Слайд 55

Which of the following devices converts heat energy into electrical energy? QUESTION 52

Which of the following devices converts heat energy into electrical energy?

QUESTION

52
Слайд 56

In the voltage divider circuit below an LED is connected in

In the voltage divider circuit below an LED is connected in

series with a resistor.
a) State the purpose of the resistor.
b) When lit, the LED has a voltage of 3.5V across it and a current of 200mA passing through it.
Calculate the unknown resistance.

QUESTION 53

Слайд 57

A light sensor circuit contains a LDR and a resistor as

A light sensor circuit contains a LDR and a resistor as

shown below.
Using the table, calculate the voltage across the LDR when the light sensor is covered.

QUESTION 54

Слайд 58

The circuit below charges a rechargeable battery during daylight hours. a)

The circuit below charges a rechargeable battery during daylight hours.
a) State

the energy transformation in the solar cell.
At a particular light level, the voltage generated by the solar cell is 1.5V.
b) Calculate the voltage across the rechargeable battery at this light level.

QUESTION 55

Слайд 59

Answer the following questions using the circuit below and the table

Answer the following questions using the circuit below and the table

provided.
a) Name component X.
b) State the purpose of component X in the circuit.
c) Explain how the circuit operates to sound the buzzer.
d) Describe a practical application for this circuit.

QUESTION 56

Слайд 60

Answer the following questions from the circuit below. a) Name component

Answer the following questions from the circuit below.
a) Name component X.
b)Explain

how the circuit works to switch the heater on. c) What is the purpose of the variable resistor.
d) Give a possible practical application for this circuit.

QUESTION 57

Слайд 61

Answer the following questions using the circuit below. a) Name the

Answer the following questions using the circuit below.
a) Name the

components X and Z.
b) What happens to the resistance of the thermistor as the temperature increases?
c)When the voltmeter reading reaches 1.8V the MOSFET switches on. Explain how the circuit operates when the temperature rises.
d) Why is component X used instead of a fixed resistance R?

QUESTION 58

Слайд 62

Answer the following question using the circuit below. a) Calculate the

Answer the following question using the circuit below.
a) Calculate the voltage

across the LDR when its resistance is 4kΩ.
b) Explain how this circuit operates when the light level falls below a certain value.
c) Give a possible practical application for this circuit.

QUESTION 59

Слайд 63

Answer the following questions from the circuit below. a) What happens

Answer the following questions from the circuit below.
a) What happens to

the voltage at point X when switch S is closed.
b) State two changes which could be made to the circuit so that the time taken for the LED to come on is reduced.

QUESTION 60